Showing posts with label SFFMU. Show all posts
Showing posts with label SFFMU. Show all posts

Friday, 29 August 2014

Trek Modelling 101: Look at that Body...


Let's run though a checklist before we start off this month's post.

We're all set with the secondary hull, saucer and engines as far as building goes which means that we must be playing with paint? I'll let +Christopher Whitford take over from here...

This month we are indeed working on painting the saucer and engineering hull of our starship. Painting a model is not as hard as it seems and can be done in a couple of easy steps.  

Painting can be done by airbrush, rattle-can (aka spray paint) or brushing by hand. For the purpose of this article we'll be using rattle-can as it's easy and since the Enterprise does not have that many colours to it you can paint it relativity inexpensively. We'll also be covering base coats and color coating as we get further in. 

The first thing you want to do is prep your saucer and engineering hull by dusting them and giving a quick sand to make sure your surface is smooth and free of dust. Next thing you want to do is go outside in a clear area so as not to let over-spray get on walls or flooring. I also recommend laying down some cardboard so you have something to sit the model above while you're painting. 

The colour I choose for this project is Model Master flat light aircraft grey. Now using a spray can for paint is not ideal as you have to use it outdoors and the weather has to be perfect to spray - and you also need to account for humidity because if that's too high paint dries to fast and can be splotchy. 

Firstly you need to run your can under hot water since this allows the paint in the can to properly disperse when it comes out of the nozzle. When spraying your model you need to do it in even strokes back and forth building up your coats. Your base coat does not completely cover your model as it provides a base for your colour coat and after you let your base coat dry you need to sand it down with a fine grit sand paper, making sure that once you finish sanding your model it is clean and free of dust and dirt.  

After that you need to apply your color coat and follow your same process as before even strokes back and forth allowing it to fully dry when you are finished your paint is smooth to the touch and with that we wrap up another month. Next month we will go over detail painting with a brush and how it adds to you model. And as always get out of her and build something.

You can catch up on all Chris' modelling tips and techniques by clicking back through the Trek Modelling 101 Archive and if that's not enough, check out the Google+ Sci-Fi Fans and Modelers' United Community


Monday, 30 June 2014

Trek Modelling 101: Warp Engines and Body Building


Last time we covered building the saucer on the AMT USS Enterprise and now we're going to move on to the warp nacelles.

Bear in mind since there are two of these so you will repeat the same steps for both. With building the nacelles you will notice the supports are already attached and lining everything up can be tricky that is where your clamps and rubber band come in real handy. 

First you will need to dry fit basically put the two halves together without glue and see if any adjustment is needed; if not you are good to glue. I recommend trimming the fitting pegs off and lining it up by hand and eye, after which tape them together and glue a little bit at a time just remember you want everything lined up squared and true. 

From there it's back to sanding again and here is a tip - while sanding a round surface be sure to sand back and forth as to not sand flat spots on the nacelles as they are supposed to be round in shape. After your first time sanding, shoot some of your handy primer on it to see if you need to putty and sand. 

Here's a tip from a friend of mine (maybe you have heard of him his name is Trekworks) for when applying putty to seam. Take two pieces of tape and lay them parallel to the seam, then take your putty and use your finger to smear it onto the seam.  Let the putty dry, remove the tape and there is your putty line for sanding all nice and neat! 

Since this kit is pretty old you will need to putty, sand, prime and repeat a couple of times until your seams are all gone. From there you just need to put it to the side and wait for the engineering section which we'll be covering now...

Secondary Moves


The Engineering section is arguably the worst piece of this kit. It has five pieces but it's the sides where the seams are that will have you screaming. 

First thing you want to do is glue the top section of the engineering hull which is in two pieces but the important thing here is the line up of the two halves so do several dry fittings first and when you are satisfied then glue. 

From there, glue the seam underneath as well to provide extra reinforcement I would also recommend taking some strip styrene and gluing it to the joint for extra extra reinforcement as this seam is known to bust time and time again. Then sand that seam smooth. 

It will take a while and you know you are done is when you take your pinky finger and run it over the surface it is smooth no stair step. Then it’s the gluing of the shuttle bay door which is really simple so just line it up and glue in place, allowing it to dry. 

Now come the time to attach the bottom to the top and this is where the nightmare comes in. 

As you are dry fitting you will notice huge seams down both sides where the top meets the bottom. Try to line it up as best you can and when you get it where you like it glue the parts together. Next comes the hard part as you will be sanding, puttying and priming several times until that seam is smooth.  When you finish, use the pinky test as described above and from there it is the front of the engineering section again as before. Line it up, glue it in place and with more puttying and sanding that ends the engineering hull.

Next time we'll be painting and detailing. Until then Get out of here and build something.

You can catch up on all Chris' modelling tips and techniques by clicking back through the Trek Modelling 101 Archive and if that's not enough, check out the Google+ Sci-Fi Fans and Modelers' United Community



Saturday, 10 May 2014

SKoST Modelling 101: If You Build It...

A little later than usual, but here's +Christopher Whitford with his third installment of Modelling 101 and it's taking shape...


Well we have talked about choosing the model you want, and the tools you will need to build the model now it is time to actually dive in and build a model. 

The model I chose is the 18 inch USS Enterprise repop from Round 2/AMT. It's a model most people have built as their first Star Trek ship and should get your feet wet with gluing, sanding puttying and painting. 

This month’s article will consist of building the saucer section as well as filling seams and priming so let’s get started. Since the saucer section on this kit consists of three pieces it should not be hard to build and it’s not, so the main thing you have to worry about is the attached sprue to the upper saucer as it's thick and difficult to remove.  Use a hobby knife for this so you must be careful. You can use a pair of wire cutters to remove the sprue but be careful and don't cut into the saucer as that will leave a spot that will have to be filled later on!

After removing the sprue from the upper and lower saucer the next thing you want to do is dry fit the two halves together.  You are going to see a seam and that seam is what you will be filling later with putty. Dry fitting makes sure everything lines up and after checking it’s time to bring out your glue (I use a liquid glue) I  can mate the two halves together and brush on the liquid glue along the seam line. I'd recommend doing this twice for added reinforcement before setting it aside to dry.

After drying I then take a sanding sponge and sand around that same seam. From there I can use my sandable bondo to fill the seam. You will have to do this multiple times to completely fill the seam as bondo does shrink as it dries. After it dries, wet your sanding sponge and sand down the bondo until you get a nice thin red line where the seam is. 

From there you'll have more filling to do on the underside of the saucer where there are three indents.They represent the phaser banks but they are not present on the studio model so fill those in and sand flush but be careful as there is raised detail that you will lose some of because of sanding smooth those indents. 

After that's finished we move on to the final piece which is the impulse engine housing. Again, dry fit and then glue after which - that’s right - more filling with putty, allow to dry and sand once more. After all that is done it’s priming time which basically means all you are doing is laying a coat of paint to see if any of your seams need to be refilled and sanded. Most likely they will so putty, sand, repeat until there no seams present on your saucer - and that is!

Now we can set aside the saucer section and end for this month. Next time we'll be building the nacelles and pylon supports as well as sanding and puttying those.  

Until next time always remember Get Out There and Build Something. 
You can look back over any of Chris' monthly articles by clicking here


Want to learn more about modelmaking from some Sci-Fi experts? Drop over to the Google+ Sci-Fi Fans and Modellers United Community for tips, chat, advice and some AMAZING photos!

Wednesday, 26 March 2014

SKoST Modelling 101: Second Edition

It's time to welcome back +Christopher Whitford for his second modelling installment - the motto of the month? Be Prepared. All yours Chris!


So you think you are ready to build your first Star Trek model? Are you all excited about putting it together, how it’s going to look when it's finished with the paint and decals?


But you have forgotten something...?

Yes that’s right  - what you're going to need to put that model together! In other words the tools of the trade. 

Some think that the model is the most expensive part of building a model but that is false it’s the tools that eat your money and yes, there are a plethora of tools to help you build a model from hobby knives to sanding sponges. However you don’t need all the tools at once to assemble a model kit. To build any model you need five basic tools and I'm going to list them here for you.


1. Glue 
The stuff that holds the model together as well as your fingers. It can be quite sticky and if not cautious, quite dangerous to your health. Now I know what you going to say; well that’s all covered so we can use superglue.

Well I'm going to say Yes and No as while they are many variants of superglue out on the market and not all are made for styrene plastic. When choosing I recommend a liquid glue such as Testors, Ambroid Pro Weld, Tenax, Tamiya Liquid Cement or ETC. Also I recommend Zap A Gap Medium CA and Zip Kicker for the modeling super glues. As far as fixing clear parts go. you can’t beat Formula 560 canopy glue as it holds clear parts without crazing them (means without fogging) your window parts.



2. Hobby Knife
You are going to need a hobby knife and while they are many out there I recommend X-Acto #1 Precision knife. It's a invaluable tool to a modeler and your toolbox should never be without it along with some refill #11 fine point blades.


3. Putty 
Again there are a lot of modeling putties such as Squadron Green and White, Perfect Plastic Putty, Epoxy Sculpt, Tamiya modeling putty - the list goes on. The two I recommend are Perfect Plastic Putty and Bondo glazing and spot putty.


4. Sandpaper
The next item you are going to need for assembly is sandpaper and there is a ton of sandpaper grades out there. Anything 400 grit and up is good for plastic models. The 400 grit grade will do your rough work while the higher grits will polish as well as sand. Myself, I use a 3M Medium/Fine sanding sponge as it contours to surfaces and does what I need it to do but watch out as you can sand away too much detail and you will be re-scribing it yourself for an age.

5. Clamps
Yes, clamps and these could be any
thing from those multi-coloured plastic mini-clamps to clothespins and rubber bands. Always remember you never ever can have too many clamps!

So there you have it the five basic tools you need to assemble a model kit. Now, here are some money saving tips for you.

1. Don’t buy your tools all at once
Buy one or two here, one there and before you know it you will have your toolbox for building models. Save yourself a bit of cash by choosing wisely.

2. Compare prices
Search around before you buy. First is not always best and you'll kick yourself if it's 20% cheaper at Retailer B.

3. Big Is Not Always Best.
Wal-mart, Lowes, Home Depot etc are not always the best option. Refer to Number Two!

4. Shop Online for Deals
Take your time and don't rush into a purchase. Get what suits your wallet - it might even be that the retailer has a better offer for you online than in the store.

Well that is it for this post. Next month we will actually start a model and I'll show you some basic modeling techniques. Until then always remember; Get out of here and Build Something!

You can look back over any of Chris' monthly articles by clicking here

Want to learn more about modelmaking from some Sci-Fi experts? Drop over to the Google+ Sci-Fi Fans and Modellers United Community for tips, chat, advice and some AMAZING photos!

Wednesday, 26 February 2014

Introducing: SKoST Modelling 101

With our increasing coverage of most (we'd be a little arrogant to say all) things Star Trek I'd like to welcome a new regular slot hosted by +Christopher Whitford, the curator of the Google+ Sci-Fi Fans and Modellers United Community.  

Chris is heavily into the Star Trek modelling world as you might have guessed and we're looking forward to learning a lot about just what it can take to transform a box of plastic parts into a replica to be proud of....


You know in the world of scale modeling you have the good ole standbys; your cars, aircraft, ships and then there are spacecraft which you can narrow down to sci-fi spacecraft and furthermore you have your Star Wars, Batman and then you get to Star Trek. 

Yes, the beloved Star Trek models and what a selection of them are out there. The classic Enterprise in a multitude of scales from 1/2500 to 1/350, the classic Klingon D-7, the Romulan Bird-of-Prey, Space Station K-7, Spock, the Exploration set, the bridge of the Enterprise, and the list goes on. 

From Enterprise to Voyager I am pretty sure there is a Star Trek model kit that you would want to build. "But how to get started?" 

I hear that question many times and the answer is the same - Research. Star Trek kits are out there for the beginner right through to the experienced modeler. 

My recommendation to the Novice Star Trek modeler is often this; the Polar Lights 1/1000 classic USS Enterprise. It is a simple kit, but by building it you will learn basics such as gap filling, seam filling, sanding, painting, applying decals and from there I would suggest a couple more of the 1/1000 kits by Round 2/Polar Lights. Just by doing those you will be surprised how you skills will increase with each model that you build. 

From there, try some of the other kits such as the AMT 18 inch Enterprise will teach you more than you will ever know due to its inaccuracies alone. These errors are well documented and there is a plethora of accurate aftermarket parts out here to help make it the star in you stash. Then there are the 1/350 scale kits that at current include the NX-01, the classic NCC-1701, and the Enterprise-A/1701 Refit which are the big boys - and big is the word coming in around three foot each and to make them stand out even more they absolutely need to be lit so another skill you will develop is how to light model kits. 


That pretty much wraps up my first post about Star Trek modeling. Next month we will go in to detail about what you will need to build your first  model and share some tips on how to do it on a budget. 

See you next time and remember get of here and go build something!

Interested in finding out more about the group? Why not drop by and take a look...HERE. 

Any questions or Star Trek modelling challenges? Why not submit a question below?